Manufacturer · Luoyang, ChinaExport & OEM support worldwide

sales@yuboo.com English

SDB-810 · 16-channel CCD · 130–700 nm / Spark OES

SDB-810Full-Spectrum CCD Direct-Reading Spectrometer

A benchtop full-spectrum spark OES with 16-channel CCD detection and 130–700 nm Paschen-Runge optics for multi-base metal analysis.

Carbon steelAluminium alloysCopper alloysNickel alloysStainless steel Application-specific configuration
Spark OES
SDB-810
YuBoo SDB-810 full-spectrum CCD direct-reading optical emission spectrometer YuBoo Instrument / Luoyang, China

01 / Why this configuration

Built around a real measurement decision.

The SDB-810 is a full-spectrum spark OES for prepared solid metal samples. It uses a 16-channel Hamamatsu/Toshiba CCD (CMOS optional), 3,648 pixels per channel and 58,368 pixels in total, with a 400 mm Paschen-Runge optical system covering 130–700 nm. The optical chamber is thermostatted at 35 ±0.1 °C, and the digital dual-pulse source operates from 200 to 800 Hz.

A benchtop full-spectrum spark OES with 16-channel CCD detection and 130–700 nm Paschen-Runge optics for multi-base metal analysis. The final specification is matched to the material range, sample form, and reporting requirement of your laboratory or production line.

16-channel Hamamatsu/Toshiba CCD (CMOS optional); 3,648 px/channel; 58,368 px total
Paschen-Runge / Rowland circle; 400 mm; 2,400 lines/mm; 130–700 nm
10 µm entrance slit; optical chamber at 35 ±0.1 °C
Full-digital dual-pulse source; 200–800 Hz; dual-spark discharge
Vacuum below 2 Pa; intermittent pumping holds >3 hours
Bases: Fe, Al, Cu, Zn, Sn, Pb, Mg, Ni, Ti and Co

02 / Configuration

Key specifications.

Use these as a starting point. Utility requirements, calibration ranges, and acceptance criteria are confirmed against the final configuration.

Have the material list or a drawing? Send it with the application so the configuration can be reviewed properly.

Request a configuration
ConfigurationVacuum or non-vacuum; non-vacuum covers Al, Mg and Zn
Detector16-channel CCD (Hamamatsu/Toshiba; CMOS optional); 3,648 px/channel; 58,368 px total
Optical systemPaschen-Runge / Rowland circle; 400 mm; 2,400 lines/mm
Wavelength range130–700 nm
Entrance slit10 µm coated slit
Optical chamber35 ±0.1 °C; vacuum below 2 Pa
Excitation sourceFull-digital dual-pulse; 200–800 Hz; dual spark
Base coverageFe · Al · Cu · Zn · Sn · Pb · Mg · Ni · Ti · Co
Argon99.999%; inlet 0.25 MPa; flow <5 L/min; standby 0.2–0.5 L/min
Readout16-bit ADC; FPGA; 16 × 100k synchronous sampling
ComputerExternal Windows computer and printer
Power220 V ±10%, 50 Hz; 200–1000 VA; 10 A slow-blow fuse
Dimensions810 × 660 × 380 mm
WeightApprox. 80 kg
Environment10–35 °C; RH 20–80%; no corrosive gas or heavy dust

Indicative configuration information. Final datasheet and performance specification are issued with the quotation and confirmed at order.

03 / Where it fits

Applications and materials.

Spark OES supports decisions across incoming material, production control, and final verification. The right method depends on the question the result has to answer.

See how we support the installation
  • Multi-base metal analysis
  • Furnace charge and melt control
  • Incoming material verification
  • Grade identification and sorting
  • Final chemical verification
  • Production records and certificates

Typical materials

Carbon steelAluminium alloysCopper alloysNickel alloysStainless steelGrey ironDuctile ironLow-alloy steelLead alloysZinc alloysMagnesium alloysTitanium alloysCobalt alloys

If your alloy or sample form is not listed, send the details. Configuration is not limited to the examples shown here — but every recommendation should be checked against the actual material and measurement target.

Before you specify

SDB-810 — practical answers.

Still deciding? Send the material and the measurement target — we will reply with a practical next step.

Ask an application engineer
What is the SDB-810 used for?

A benchtop full-spectrum spark OES with 16-channel CCD detection and 130–700 nm Paschen-Runge optics for multi-base metal analysis. The configuration is matched to the material range, sample form and reporting requirement of the laboratory or production line.

Which materials and sample forms does the SDB-810 cover?

Typical materials: Carbon steel, Aluminium alloys, Copper alloys, Nickel alloys. Typical tasks: multi-base metal analysis, furnace charge and melt control. If the material or sample form is not listed, send the details before committing — the configuration is not limited to the examples shown.

What are the key specifications of the SDB-810?

Starting point: configuration Vacuum or non-vacuum; non-vacuum covers Al, Mg and Zn; optical system Paschen-Runge / Rowland circle; 400 mm; 2,400 lines/mm; wavelength range 130–700 nm. These figures are indicative; utility requirements, calibration ranges and acceptance criteria are confirmed with the final configuration.

How is the configuration confirmed before ordering?

Send the material list, the sample form, the standard and the decision the result has to support. We confirm the configuration in the quotation, and a sample test can be arranged where the result is critical.

Put it to work

Configure SDB-810 around your material.

Send the alloy, sample form, elements of interest, and the decision the result needs to support. We will recommend a configuration and confirm the next step.